INTRODUCTION:
This circuit utilises the RF module (Tx/Rx) for making a wireless remote, which could be used to drive an output from a distant place. RF module, as the name suggests, uses radio frequency to send signals. These signals are transmitted at a particular frequency and a baud rate. A receiver can receive these signals only if it is configured for that frequency.
A four channel encoder/decoder pair has also been used in this system. The input signals, at the transmitter side, are taken through four switches while the outputs are monitored on a set of four LEDs corresponding to each input switch.
The circuit can be used for designing Remote Appliance Control system. The outputs from the receiver can drive corresponding relays connected to any household appliance.
DESCRIPTION:
This radio frequency (RF) transmission system employs Amplitude Shift Keying (ASK) with transmitter/receiver (Tx/Rx) pair operating at 434 MHz. The transmitter module takes serial input and transmits these signals through RF. The transmitted signals are received by the receiver module placed away from the source of transmission.
The system allows one way communication between two nodes, namely, transmission and reception. The RF module has been used in conjunction with a set of four channel encoder/decoder ICs. Here HT12E & HT12D have been used as encoder and decoder respectively. The encoder converts the parallel inputs (from the remote switches) into serial set of signals. These signals are serially transferred through RF to the reception point. The decoder is used after the RF receiver to decode the serial format and retrieve the original signals as outputs. These outputs can be observed on corresponding LEDs.
Encoder IC (HT12E) receives parallel data in the form of address bits and control bits. The control signals from remote switches along with 8 address bits constitute a set of 12 parallel signals. The encoder HT12E encodes these parallel signals into serial bits. Transmission is enabled by providing ground to pin14 which is active low. The control signals are given at pins 10-13 of HT12E. The serial data is fed to the RF transmitter through pin17 of HT12E.
Transmitter, upon receiving serial data from encoder IC (HT12E), transmits it wirelessly to the RF receiver. The receiver, upon receiving these signals, sends them to the decoder IC (HT12D) through pin2. The serial data is received at the data pin (DIN, pin14) of HT12D. The decoder then retrieves the original parallel format from the received serial data.
When no signal is received at data pin of HT12D, it remains in standby mode and consumes very less current (less than 1µA) for a voltage of 5V. When signal is received by receiver, it is given to DIN pin (pin14) of HT12D. On reception of signal, oscillator of HT12D gets activated. IC HT12D then decodes the serial data and checks the address bits three times. If these bits match with the local address pins (pins 1-8) of HT12D, then it puts the data bits on its data pins (pins 10-13) and makes the VT pin high. An LED is connected to VT pin (pin17) of the decoder. This LED works as an indicator to indicate a valid transmission. The corresponding output is thus generated at the data pins of decoder IC.
A signal is sent by lowering any or all the pins 10-13 of HT12E and corresponding signal is received at receiver’s end (at HT12D). Address bits are configured by using the by using the first 8 pins of both encoder and decoder ICs. To send a particular signal, address bits must be same at encoder and decoder ICs. By configuring the address bits properly, a single RF transmitter can also be used to control different RF receivers of same frequency.
To summarize, on each transmission, 12 bits of data is transmitted consisting of 8 address bits and 4 data bits. The signal is received at receiver’s end which is then fed into decoder IC. If address bits get matched, decoder converts it into parallel data and the corresponding data bits get lowered which could be then used to drive the LEDs. The outputs from this system can either be used in negative logic or NOT gates (like 74LS04) can be incorporated at data pins.
CIRCUIT DIAGRAM:
Click to enlarge the circuit.
COMPONENTS:
Flowing are the components used click to download their Datasheets.
HT12D Decoder IC [DATASHEET DOWNLOAD]
HT12D is a decoder integrated circuit that belongs to 212 series of decoders.
HT12E Encoder IC [DATASHEET DOWNLOAD]
RF Module (Transmitter & Receiver)
Pin No | Function | Name |
1 | Ground (0V) | Ground |
2 | Serial data input pin | Data |
3 | Supply voltage; 5V | Vcc |
4 | Antenna output pin | ANT |
RF Receiver
Pin No | Function | Name |
1 | Ground (0V) | Ground |
2 | Serial data output pin | Data |
3 | Linear output pin; not connected | NC |
4 | Supply voltage; 5V | Vcc |
5 | Supply voltage; 5V | Vcc |
6 | Ground (0V) | Ground |
7 | Ground (0V) | Ground |
8 | Antenna input pin | ANT |
sir please tell me which encoder/decoder ic to use if we want more than 4 functions
c the components section on this project page .. data sheets are also given .. and you can google encoders with more in/out pins and replace in the circuit
what will be the circuit if i want to control my home appliances with RF?
Anonymous --- use of diode. with use of diode,u make 16 inputs
HT640/HT648L
Can I use PWM signal as input to
these Encoder for wireless motor
control purposes. ..Along with this
circuit below
http://gadgetronicx.blogspot.com/2013/09/dc-motor-speed-controller-using-ic-555.html